Home > Chainsaw >

Hyway Husqvarna 350, 351, 353 Nikasil plated cylinder kit 45mm

Hyway Husqvarna Chainsaw cylinder kit for Husqvarna 350, 351, 353 chain saws


 
Alternative Views:


Our Price: $119.94
Sale Price: $99.95
Part #: H30353

Important:

Warranty for a New Cylinder Kit.pdf


Options:

Order Direct from the Factory

Proposition 65 Warnings:

www.p65warnings.ca.gov



Stock Status:In Stock

Qty:

Description Replaces the following OEM(s)
 
Hyway brand cylinder kit. 45mm bore.
High quality Nikasil plated Closed port. This is the best cylinder available for these saws.
Fits: Husqvarna 350, 351, 353 chainsaw. Also works as a big bore for 346xp.
Includes: cylinder, piston, ring, wrist pin, cir clips
Replaces OEM part: 537 25 31-02
Fits models:
  • Husqvarna 350, 351, 353

You may also like...
Piston ring compressor tools kit
Sale Price: $12.95
Part #: S97419

Add
Piston ring compressor tools kit

Average Customer Review: Average Customer Review: 4.5 of 5 4.5 of 5 Total Reviews: 13 Write a review.

  0 of 0 people found the following review helpful:
 
1 of 5 Unacceptable in Two Ways July 18, 2020
Reviewer: Toons from Hertford, NC United States  
I purchased this kit to put into my Husqvarna 350 that I ran too hot and destroyed the piston.  I purchased this kit because I thought that the price indicated that it was higher quality than the $40 kits that I saw.  I was wrong.  After installation, the flywheel actually rubbed the side of the cylinder so hard that it would not turn.  There is no way that the cylinder can be installed with a misalignment because of the tight tolerances on the head bolts.  This is just a bad casting or a very bad casting design.  I had to uninstall and file down the edge of my flywheel to make it work.  Additionally, the cylinder on the 350 has an upper and lower part.  No gasket was provided.  It does come with the $40 kits.  The casting is not identical to the original.  The original is made of separate parts that are bolted together.   Again, the $40 kits have this same feature.  Finally, the finished machine is hard to start and does not run as strong as it did.   $ does not equal quality.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Nice cylinder. Plating looks great. January 25, 2020
Reviewer: RT from Greencastle, PA United States  


Was this review helpful to you?

  0 of 1 people found the following review helpful:
 
3 of 5 Hyway Husqvarna 350 Nikasil plated cylinder September 23, 2019
Reviewer: Anonymous Person from Ocala, FL United States  
My local repair center agreed to install the Nikasil plated cylinder that I purchased for my Husqvarna 350 chain saw.  It was a successful repair however,...

Afterwards, I discovered this and it gives me concern.

" with Nikasil cylinder bore linings are particularly vulnerable to fuel (gasoline or petrol) with a high sulfur content.

The sulfur in the fuel breaks up the Nikasil lining in the cylinders, thus causing a loss of compression. Once the lining is damaged, excessive bore wear of the soft, underlying alloy occurs very quickly. Some Nikasil engines have failed in as little as 30,000 miles. And the effect is cumulative, so if the engine has ever been run on high sulfur fuel, the damage may already have been done and premature bore wear may result.

Some symptoms of the Nikasil problem are rough running at idle and difficult cold starting, both due to loss of compression. In severe cases, the loss of compression is so bad that the engine loses power."




Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 January 15, 2018
Reviewer: Willie Nelson from Live Oak, FL United States  
These items was just what I needed to do the job. & of good quality.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Piston Cyl Kit March 9, 2017
Reviewer: Glenn Brown from Hampton, VA United States  
Fit was excellent saw ran great

Was this review helpful to you?

View All Customer Reviews